Toolsky

Free Online Tools & Utilities for Every Task.

Ohm's Law Calculator

Calculate Voltage, Current, Resistance, and Power instantly by entering any two known values.

V
A
Ω
W

Enter any two values to calculate the others.

Calculated Values

Every circuit question — will this resistor survive, how much current will that motor draw, what voltage is left at the end of a long cable — comes back to one compact relationship between four quantities. This Ohm's law calculator works out voltage, current, resistance and power for you: enter any two of them and it calculates the other two instantly, without you having to rearrange formulas on paper.

The Triangle That Runs Electronics

Ohm's law states that voltage equals current multiplied by resistance: V = I × R. Georg Ohm published the relationship in 1827, and it remains the first tool of everyone who works with electricity, from hobbyists wiring an LED to engineers sizing industrial equipment. Add the power relationship, P = V × I, and the four quantities lock together so tightly that knowing any two determines the rest.

The units matter as much as the numbers. Voltage is measured in volts (V), current in amperes (A), resistance in ohms (Ω) and power in watts (W). Keep those straight and the formulas never produce nonsense; mix in milliamps or kilohms without converting and they happily will.

What This Calculator Works Out

  • Voltage when you know current and resistance, or current and power
  • Current when you know voltage and resistance, or power and voltage
  • Resistance when you know voltage and current, or power and current
  • Power in watts from any valid pair of the other three values
  • All four values displayed together, so you can sanity-check the whole picture at once

It pairs naturally with the electricity cost calculator when you want to turn watts into running costs, and with the power converter when results need expressing in kilowatts or horsepower.

How to Use the Calculator

  1. Decide which two values you already know from your circuit, component or appliance label.
  2. Enter those two values in their fields, taking care to use volts, amps, ohms and watts as the units.
  3. Leave the two unknown fields empty.
  4. Run the calculation and read the completed set of four values.
  5. Double-check the result against reality: if a resistor is expected to dissipate several watts, confirm its physical power rating before building anything.

A Worked Example: Sizing a Resistor for an LED

Say you are powering a small circuit from a 12 V supply and a component draws 0.5 A. Enter voltage 12 and current 0.5. The calculator returns resistance R = V ÷ I = 12 ÷ 0.5 = 24 Ω, and power P = V × I = 12 × 0.5 = 6 W. That power figure is the one people forget: a standard quarter-watt resistor in that position would overheat, so you would choose a part rated comfortably above 6 W. Two typed numbers just prevented a burnt component.

Tips, Limitations and Common Mistakes

The classic error is unit slips — entering 500 when you mean 500 mA (0.5 A) throws every result off by a factor of a thousand. The second is forgetting that real components have tolerances and temperature effects, so a calculated value is a target, not a promise engraved on the part.

Understand the model's limits. Ohm's law in this simple form describes resistive, linear behaviour. It applies beautifully to resistors, heaters and lamps, and approximately to many real circuits, but it does not capture reactive components (capacitors and inductors) in AC circuits, semiconductors whose resistance changes with voltage, or batteries with meaningful internal resistance unless you model those separately. Power calculated here is electrical power converted in the component; for motors, some of that becomes heat and some motion, so treat the wattage as an input figure rather than a measure of mechanical output.

Note: results are calculated estimates for learning and planning. For mains wiring, installations or safety-critical work, consult a qualified electrician and your local electrical code.

A companion idea worth understanding is the voltage drop across a component. In a series circuit the supply voltage is shared between the parts in proportion to their resistances, which is why a long thin cable can leave a motor underpowered: the cable itself behaves like a resistor and keeps a slice of the voltage. The same four formulas let you estimate that drop — multiply the cable's resistance by the current it carries — and decide whether a thicker conductor belongs in the design before anything is installed.

Frequently Asked Questions About the Ohm's Law Calculator

What is the formula for Ohm's law?

V = I × R: voltage equals current times resistance. Rearranged, I = V ÷ R and R = V ÷ I. Power adds P = V × I, which can be combined into P = I²R or P = V² ÷ R.

Which two values should I enter?

Whichever two you know. Any pair among voltage, current, resistance and power is enough, because the relationships determine the remaining two uniquely.

Why does my resistor get hot even though the circuit works?

Because it is dissipating the calculated power as heat. If the watts figure approaches or exceeds the resistor's rating, choose a higher-rated part or a different resistance.

Does Ohm's law work for AC circuits?

For purely resistive AC loads it works with RMS values. Circuits with significant inductance or capacitance need impedance calculations, which go beyond this calculator.

Can I calculate what resistor I need for an LED?

Yes. Subtract the LED's forward voltage from your supply voltage, then divide by the LED's target current in amps. The calculator confirms the resistance and the power the resistor must handle.

What is a milliohm or a kilohm in this calculator?

Enter values in plain ohms. A kilohm is 1,000 Ω and a milliohm is 0.001 Ω, so convert first: type 4700 for a 4.7 kΩ resistor.

Why are my results slightly different from a measured circuit?

Real components have tolerance bands (often ±5%), leads and contacts add resistance, and meters have their own error. Small differences between calculation and measurement are normal.

Four Numbers, One Relationship

Keep V = I × R and P = V × I in your pocket and most everyday circuit questions answer themselves. This calculator simply does the rearranging and arithmetic for you, so you can spend your attention on choosing the right components instead of double-checking algebra.